[Weather] [personal] Anemometer not detected?

[Barry]

So in reading more on the list I found the 1 wire viewer.

It shows I have the following devices

3100000000EC8A20   DS2450   1-wire quad AD Converter
DB0008001B34FE10   DS1920   Digital Thermometer
EE00000025CD3981   DS1990A   65-bit unique serial number
D9000000017CA71D   DS2423  1-wire counter with 4096 bits of mem

The last device (1D) does not show up with the oww command "assign"

I suspect it is the Anemometer. So I manually placed it in the devices file.

I am now back to the message "Checking weather station "Anemometer" not
found" when I start the software.
Also running   "? devices"   shows the T1 and vaneadc sensors only.

Still stumped

Barry






----- Original Message ----- 
From: "Barry" <barrymw at pacbell.net>
To: "List for 1 Wire Weather Stations and devices" <weather at buoy.com>
Sent: Sunday, October 01, 2006 12:32 PM
Subject: Re: [Weather] [personal] Anemometer not detected?


> I am extremely new to 1 wire devices. So if a counter ends with "1D" how
do
> I identify an "81" device?
> Maybe we are looking at a batch of units built with "81" devices?
>
> Barry
>
> ----- Original Message ----- 
> From: "Jim Pace" <unkajim at comcast.net>
> To: "List for 1 Wire Weather Stations and devices" <weather at buoy.com>
> Sent: Sunday, October 01, 2006 12:21 PM
> Subject: Re: [Weather] [personal] Anemometer not detected?
>
>
> > Shouldn't all counter addresses end in "1D" such as my anemometer
counter:
> > CE000000018A611D ?
> > Jim
> > http://ecapmiill.home.comcast.net
> > ----- Original Message ----- 
> > From: "Barry" <barrymw at pacbell.net>
> > To: <weather at buoy.com>
> > Sent: Sunday, October 01, 2006 11:58 AM
> > Subject: [personal] [Weather] Anemometer not detected?
> >
> >
> > > Hi all,
> > > I am attempting to use the OWW software on a Linksys NSLU2 "Slug".
> > > The modification to the Slug went very well. I am having problems with
> > > detecting the Anemometer.
> > >
> > > I am able to read direction and temp but not wind speed.
> > >
> > > I am using the USB adaptor with the very short curly cable supplied.
> > > I have tried manually placing the following line in the devices file.
> > > anem EE00000025CD3981 1.000000
> > >
> > > Placing the line in the devices stopped the Anemometer not found
> messages.
> > > Assign now lists all three sensors.
> > >
> > > But still no wind speed readout?
> > >
> > > I am worried by a previous post on this list claiming that the source
> code
> > > show that Anem sensors must end with "1D" and mine ends with "81"  ??
> > > Sensors were purchased last week. Is it possible that new devices now
> end
> > > with "81" and are not functional?
> > >
> > >
> > > Any and all help much appreciated
> > >
> > > Barry
> > >
> > >
> > > _______________________________________________
> > > Weather mailing list
> > > Weather at buoy.com
> > > http://www.buoy.com/mailman/listinfo/weather
> >
> >
> > _______________________________________________
> > Weather mailing list
> > Weather at buoy.com
> > http://www.buoy.com/mailman/listinfo/weather
> >
>
>
> _______________________________________________
> Weather mailing list
> Weather at buoy.com
> http://www.buoy.com/mailman/listinfo/weather
>